How To Install Dvd Drive In Pc

The optical drive, whether it is the old-schoolhouse DVD format or the more than modern Blu-ray, is becoming less common as more of our data moves online, merely information technology's all the same a useful component to have in your PC.

Depending on its historic period, your optical drive might have a SATA connector

or an older IDE connector.

Installing an optical bulldoze is fairly like shooting fish in a barrel, merely you must sympathise how they connect. This article walks you through the process.

Step 1: Fit the Device into the Bulldoze Bay

Starting time, find and fit the optical drive into a spare 5.25-inch bulldoze bay within the case. Some cases, such as those plant in select ASUS computers, accept flaps on the front to hide the optical drives from view. Those models require removal of the front panel in most situations.

If you have a screwless drive bay blueprint or i with runners, consult your computer manual for total instructions.

Other cases require you to spiral the bulldoze into place from the sides. The optical bulldoze gets pushed into the example from the forepart, and that is where removing the front end panel comes into play. The forepart of the bulldoze needs to be flush with the case (flap-free models) or slightly further back for cases with flaps in the front end.

To identify where the drive should be, push it in until the screw holes on one side line upward with the round screw holes on the bay'southward sidewalls. Utilise the four screws (provided with the optical bulldoze or instance) to hold the drive securely in place. There are usually iv screws in total.

Footstep ii: Connect the EIDE or SATA Cablevision into the Drive

The second footstep to installing an optical drive is to attach the data cables to the device. The process depends on whether you take a SATA or EIDE DVD/Blu-Ray bulldoze.

Connecting SATA Plugs into the Drive

SATA optical drives feature a slim plug that features a right-angle notch, ensuring it merely fits i way.

Gently button the plug into the bulldoze's socket, and so cheque that it is parallel with the drive's back finish. When in place, apply firm pressure to ensure the connectedness is secure.

Connecting EIDE Cables into the Drive

IDE (technically EIDE) optical drives include a 40-pin, 80-wire cable that is much wider and more difficult to insert. The EIDE cablevision only fits one manner due to a protruding cardinal design in the connector's eye section.

Insert one side of the connector at a slight angle, and then partially insert the other side so that the plug is fifty-fifty. Next, push the unabridged connector (with medium force) into the socket on the drive. The slight angle method ensures the beginning pins align properly earlier inserting, which prevents forced bends.

Once you verify that all pins line upwards, give the connector a house push to ensure it goes in all the way. This process requires patience since the plug is difficult to fit into the opening. You don't want to curve those pins or push besides hard if one was not lined up correctly.

TIP: If you're installing more than than one IDE drive, y'all'll demand to set the jumpers on the rear so that one drive gets gear up as master and the other set to slave. Almost drives have a diagram on top.

Footstep iii: Insert the Power Cable

Once you take installed the optical drive and continued the data cable, information technology is fourth dimension to attach the power cables.

Inserting SATA Power Plugs into the Drive

DVD/Blu-Ray drives and recorders typically use the SATA connection. The SATA power cable is slim and flat.

Find an available power plug and insert it into the optical drive.

Inserting MOLEX Power Plugs into the Drive

Older DVD drives with an EIDE connection apply a Molex ability connector. This plug is a large (compared to other PC plugs) white or black four-pivot connector coming from your power supply. Locate a free one and push information technology into the bulldoze's ability socket. Utilize a fleck of forcefulness to ensure proper connexion. Give the plug a GENTLE tug to brand certain information technology'southward secure.

4. Fit the IDE or SATA Cable into the Motherboard

With all connections hooked up on the optical bulldoze, you're prepare to plug the cable into the motherboard.

The same insertion method used on the optical drive applies to the motherboard. The SATA socket includes the same right-angle design to prevent plugging information technology in the wrong way. You should hear a click once the connector is in place.

An EIDE motherboard socket connects the same mode as the optical bulldoze, except you often have two color options. Ordinarily, blue is the primary connection, and white gets used for the second EIDE controller on the lath. However, some motherboards include white EIDE sockets merely, i blackness plus ane white, or a different color from the norm.

Regardless of IDE colors, the motherboard's EIDE connections get out pin 20 empty. Some plugs block off that pin as a secondary protective measure to ensure a correct fit on the board.

You can always bank check your motherboard's manual for specifications and location information. The IDE connector plugs in one way just, thank you to that previously mentioned notch design in the EIDE socket. Push button the cable in gently and as directly as possible to avoid bending any pins.

Now that all connections are attached and secured, you tin turn on your PC and let it notice the new bulldoze at boot and in Windows.

Source: https://www.alphr.com/features/378928/how-to-install-an-optical-drive/

Posted by: cannadygles1968.blogspot.com

Share this post